When only one fixture has low water pressure, the problem can likely be remedied if you just focus on fixing that one fixture or the pipes serving it since it may involve a clogged showerhead or leaky pipe, for example. But widespread water pressure issues affecting the whole house indicate different problems. If your home water pressure seems low, then the first thing to do is to narrow down the cause.
Is the Water Meter Valve Fully Open?
In many homes, there are two major shutoff valves controlling water to the home. The first is the water meter valve, located right next to the water meter on the main city supply pipe serving your home. Normally, you will not use this valve, as technically it belongs to the water company and is typically used only by water company personnel. But if your water pressure is low throughout your house, especially after some work has been done on your plumbing system, it’s possible that this valve is not fully open.
How to fix it: If you have recently had a repair done and are now noticing a reduction in the water pressure throughout your house, check the meter valve. It may be located on an outside wall of the house (in warm climates), in an underground box between the house and the street, or in an interior utility area, such as a basement or attached garage. The valve is fully open when the valve handle (which may be just a metal tab that is turned with a special wrench) is parallel to the water pipe. If the handle is set at an angle to the pipe, it is not fully open.
Is the Main House Shutoff Valve Open?
The other main shutoff valve is the home’s shutoff, usually located inside the house, near where the main city supply pipe enters the home through the foundation wall. In warm climates, the main shutoff may be outdoors. As with the water meter valve, this main shutoff valve is sometimes left partially closed after some kind of repair has been done to the system. If your water pressure has mysteriously lessened after a recent repair, there is a good chance that the valve wasn’t fully opened after the repair was completed.
How to fix it: Make sure this valve is fully open. If this is a gate valve, indicated by a wheel-like handle, make sure the handle is turned fully in the counterclockwise direction. If it is a ball valve, indicated by a lever handle, the handle must be parallel to the pipe direction to be fully open.
Is the Pressure Regulator Failing?
Another common cause for home water pressure problems is a faulty pressure regulator or pressure-reducing valve. A pressure regulator is a control valve that reduces the input pressure in your plumbing system to a safe level that will not damage your pipes. Not all homes have them, but for those that do, a failing pressure regulator can cause a serious upward spike in water pressure. It can also have the opposite effect: sudden low water pressure. When the pressure regulator fails, you will notice the effect on all of the fixtures in the home, and it will happen rather suddenly.
How to fix it: Though this is not a quick fix, this tip can help you understand if your regulator is at fault. To get an accurate reading of the water pressure in your house, test the pressure by attaching a water pressure gauge to the outdoor hose spigot closest to the water main or pressure regulator. Recommended water pressure is about 75 pounds per square inch depending on where you live. If your pressure tests very low, this may indicate a failed pressure regulator that needs to be replaced, typically requiring professional help.
Do You Have Old Steel Water Pipes?
The most serious and potentially expensive reason for low water pressure occurs when old galvanized steel water pipes are corroded to the point that water flow is significantly restricted. These pipes corrode on the inside (so you usually can’t see the corrosion), but over time, the buildup of corrosion and scale gradually closes off the pipe. This problem develops over decades, so the reduction in water flow is very gradual; you will not notice a sudden pressure drop. However, if you move into an old house with steel pipes, the pipes may have significant corrosion to start with and the problem may worsen relatively quickly.
How to fix it: Unfortunately, the only solution for corroded pipes is to re-pipe the system with new copper or plastic water supply piping. It is the only way to solve the problem. Usually the best option for re-piping these days, in terms of cost and ease of installation, is to use PEX tubing rather than copper pipe.
When to Call a Professional
If the problem is a valve, opening it will likely immediately increase your water pressure. But some of these repairs may require additional help, such as any repair or replacement piping that needs to be done. In addition, if the pressure regulator is failing and needs replacement, you may need help. Although a pressure regulator can sometimes be replaced by yourself with the same brand and size, in most cases is it better to call a professional to take care of it. Replacing it requires shutting off the water to the home at the water meter shutoff valve.
